• Pulse Analog 1.5kw AC Servo Control System For Sewing Machine
  • Pulse Analog 1.5kw AC Servo Control System For Sewing Machine
Pulse Analog 1.5kw AC Servo Control System For Sewing Machine

Pulse Analog 1.5kw AC Servo Control System For Sewing Machine

Product Details:

Place of Origin: China
Brand Name: Vector
Certification: CE
Model Number: VEC-VC1-00623MC-M-E /130MB-1R525A23F-CF2

Payment & Shipping Terms:

Minimum Order Quantity: 1 kit
Price: To Be Discussed
Packaging Details: 375*290*155mm, 280*208*112mm
Delivery Time: 5-8 work days
Payment Terms: L/C, T/T, Western Union
Supply Ability: 500-1000 kits /Month
Get Best Price Contact Now

Detail Information

Phase: Three Phase Voltage: 220V
Model: VEC-VC1-00623MC-M-E /130MB-1R525A23F-CF2 Usage: Sewing Machine
Certifictaes: CE Encoder: 2500 Pulse Incremental + Hall Encoder;
Communication Protocols: Modbus/CANopen/EtherCAT Power: 1.5KW
High Light:

Sewing Machine AC Servo Control System

,

Analog 1.5kw AC Servo Control System

,

Pulse Analog 1.5kw AC Servo System

Product Description

220V 1.5kw Pulse/Analog AC Servo Driver System For Sewing Machine

 

Pulse/Analog AC Servo Driver System
AC Power 1.5KW
Three Phase 220V
Modbus / CanOpen / EtherCAT
Location / Speed / Torque Control Mode

2500 pulse incremental + Hall encoder;

Products Features

Product Name Pulse/Analog AC Servo Driver System
Brand Vector
Model No. VEC-VC1-00623MC-M-E /130MB-1R525A23F-CF2
Power4 1.5KW
Voltage 220V
Phase Three Phase
Rated Current 6A
Communication Protocols Modbus/CANopen/EtherCAT
Encoder 2500 pulse incremental + Hall encoder;

 

Voltage Control Mode Single-phase / three-phase full-controlled rectification
SVPWM modulation
Encoder Encoder Feedback 2500 pulse incremental + Hall encoder;
2500 pulse incremental;
17bit Tamagawa absolute encoder;
23bit Tamagawa absolute encoder;
24bit Nikon absolute encoder;
Pulse Command Input Pulse Type Differential input,Open collector
Frequency Range Differential input:0-500kHz,pulse width greater than 1us
Open collector: 0-300kHz,pulse width greater than 2.5us
Pulse Mode pulse + direction; AB pluses; CW+CCW;
Analog Input Voltage Range -10V to 10V
Input Impedance 10kΩ
Maximum Frequency 1.5kHz
DI/DO Interface Type NPN/PNP
Communication Modbus/CANopen/EtherCAT
Location Mode Command Input Method Pulse Command
Internal Planning Position

Plan by target position, speed, acceleration and deceleration
time

Trapezoidal speed curve
Cubic speed curve
Absolute / relative command mode
Instruction Smoothing Mode Low Pass Filtering / Median Filtering
Electronic Gear Ratio N/M;(M=1~2147483647,N=1~2147483647)
Torque Limit Internal Torque Limit / Analog Torque Limit
Feedforward Compensation Speed Feedforward / Torque Feedforward
Torque Compensation Fixed Torque Compensation / Analog Torque Compensation /
Automatic Torque Compensation;
Speed Contol Mode Command Input Type Pulse Frequency / Analog / Internal Planning Speed
Speed Control Range 1~max speed
Bandwidth 1kHz
Torque Limit Internal Torque Limit / Analog Torque Limit
Instruction Smoothing Mode Low Pass Filtering / Median Filtering
Feedforward Compensation Torque feedforward
Torque Compensation Fixed Torque Compensation / Analog Torque Compensation /
Automatic Torque Compensation;
Torque Control Mode Command Input Type Internal Torque Reference / Analog Control Torque
Torque Compensation Fixed Torque Compensation / Analog Torque Compensation /
Automatic Torque Compensation;
Speed Limit Internal Speed Limit / Analog Speed Limit

 

Pulse Analog 1.5kw AC Servo Control System For Sewing Machine 0

 

Servo Drive model slecting:

 

Pulse Analog 1.5kw AC Servo Control System For Sewing Machine 1

Servo motor model slecting:


Pulse Analog 1.5kw AC Servo Control System For Sewing Machine 2

 

Pulse Analog 1.5kw AC Servo Control System For Sewing Machine 3Pulse Analog 1.5kw AC Servo Control System For Sewing Machine 4Pulse Analog 1.5kw AC Servo Control System For Sewing Machine 5

Installation Precautions

● Install the driver on a dry and sturdy platform. Maintain good ventilation and

heat dissipation during installation and maintain good grounding.

● Please install in the specified direction to avoid malfunction.

● When installing, please ensure that the servo driver is kept at a specified

distance from the inner surface of the cabinet and other machines, otherwise it may cause fire or malfunction.

Installation
Environment
Requirements
Atmospheric Pressure 86~106kPa
Mbient Humidity 0~55℃
Ambient Temperature 0~90%RH
IP Rating IP20
Vibration 0~4.9m/s^2

 

 

Operating precautions:

 

● in the test operation, in order to prevent accidents, please test the servo motor with no load

(not connected to the driver shaft), otherwise it may cause injury.

● when starting to operate on the supporting machine, set the user parameters that match the machine

in advance. If you start operation without parameter setting, it may cause mechanical loss or malfunction.

● to avoid accidents, install a limit switch or a stopper at the end of the movable part of the machine,

otherwise it will cause mechanical damage or injury.

● do not make extreme changes to the parameter settings, as this may result in

unstable operation, mechanical damage or injury.

●when the power is turned on or the power supply is cut off, the heat sink of the servo driver, external

braking resistor, motor, etc. may be in a high temperature state. Do not touch it, otherwise it may cause burns.

● when using a servo motor on the vertical axis, set a safety device to prevent the work piece from falling

under alarm, over travel, etc. In addition, please perform the servo lock stop setting when an over travel occurs,

otherwise the work piece may fall in the over travel condition.

● do not enter the operating range of the machine during operation, otherwise it will cause injury.

● do not touch the servo motor or the movable part of the machine during

operation, otherwise it will cause injury.

● please set up the safety system to ensure safety even in the event of a signal

line breakage. For example, when the positive over travel switch (P-OT) and negative over travel switch

(N-OT) signals are disconnected at the factory setting, they operate safely.

● be sure to set the servo OFF state when turning off the power.

● do not turn the power on/off frequently. After the actual operation starts, the power ON/OFF interval

should be more than 1 hour, otherwise the components inside the servo unit will be prematurely aged.

●when an alarm occurs, reset the alarm after the cause is removed and ensure

safety, and restart the operation, otherwise it may cause injury.

● do not use the brake of the brake motor for normal braking, otherwise it may

cause a malfunction.

 

Maintenance and inspection Precautions

● do not change the wiring while the power is on, otherwise it may cause electric shock or injury.

● please perform wiring or inspection by professional technicians, otherwise it

may cause electric shock or product failure.

● please check the power after the power is off for at least 5 minutes. Even if the power is turned off,

high voltage may remain inside the servo drive. Therefore, do not touch the power terminal within 5

minutes after the power is turned off, otherwise it may cause electric shock.

●when replacing the servo drive, please back up the servo driver user parameters to be replaced

before the replacement, and transfer the backup to the new servo drive, and then restart the operation,

otherwise the machine may be damaged.

 

Packing and Shipping

Packing details of Servo Drive
Products E1(3-6A) E2(7-12A) E3(16-27A) C015(32-38A) C022(45-60A)
Ctn. Size 280*208*78 280*208*112 375*290*155 440*296*288 510*305*325
Packing details of Motion Controller
Products VA Motion VA Expansion VE Motion VE Expansion(32) VE Expansion(76)
Ctn. Size 176*165*78 127*75*70 144*128*69 176*164*78

316*164*78

 

 

Delivery Time

Quantity 1-5 kits 50-100 kits 200-500 kits
Delivery time Within 3 days 5-10 days 15-25 days

 

1. For small order we always can delivery out within 1 week.

2. Our products can be shippied via Air, Land or Sea.

 

Accessories

 

  Accessory name Image  
Satandard Spare Parts Power terminal Pulse Analog 1.5kw AC Servo Control System For Sewing Machine 6 Adapt to E1,E2 structure drive
Cn3 encoder plug Encoder plug on the driver side
Cn4 control terminal plug Input/output signal terminals,user wiring
Encoder connection line The standard cable length is 3, 5, 8, 10, 13, 15 meters, according to customer
needs Provide independent connector
Power line The standard cable length is 3, 5, 8, 10, 13, 15 meters, according to customer
needs Provide independent connector
Drive monitoring line Connect and adjust the software for remote monitoring and firmware update
Purchasing Spare Parts USB to RS232 Adapter cable If necessary, self purchase
Ethernet communication line If necessary, self purchase

 

CE Certificates

1. CE (EU Safety Standard);
2. IEC/EN61800-5-1:2007 (Safety requirements for electrical, thermal and energy in Section 5-1 of the

variable speed electric driver system), corresponding to the national standard GB12668.501-2013;

3, IEC / EN61800-3: 2004 + A1 (speed control electric driver system part 3 electromagnetic compatibility

standards and its specific test methods), corresponding to the national standard GB12668.3-2012.

Pulse Analog 1.5kw AC Servo Control System For Sewing Machine 7

Our Team

Pulse Analog 1.5kw AC Servo Control System For Sewing Machine 8

Want to Know more details about this product
I am interested in Pulse Analog 1.5kw AC Servo Control System For Sewing Machine could you send me more details such as type, size, quantity, material, etc.
Thanks!
Waiting for your reply.